{"reviews":[],"product":{"platform_product_id":"1607412219977","star_distribution":{"1":0,"3":0,"2":0,"5":0,"4":0},"name":"DuroMax XP18HPE 440cc 18-Hp 3,600-Rpm 1-Inch Shaft Electric Start Engine","average_stars":"0.0","review_images":[],"review_number":0,"variants":[],"id":472601},"review_page_count":1,"questions":[{"answer":"Please call (844-DuroMax) or email (support@duromaxpower.com) our Service Department for assistance. ","question":"If the needle in the carburator sticks open allowing the fuel from the carb bowl to overfill in the crankcase within the warranty period of the engine, what would be done?","id":7650},{"answer":"Absolutely, non-ethanol fuel will be better for storage than ethanol mixed fuel.","question":"I just received my 10k generator It has an 18hp Can I use none ethanol gas?","id":7627},{"answer":"Absolutely, non-ethanol fuel will store better than ethanol mixed fuel.","question":"I just received my 10k generator It has an 18hp Can I use none ethanol gas?","id":7625},{"answer":"The XP18HPE is not CSA approved at this time. Keep checking back, DuroMax 1st two CSA generators will be available soon.","question":"Who sells this motors in Canada. We really would like to order one . Harold Sattler ","id":6058},{"answer":"A multi-meter would read voltage exceeding 12vdc at the battery while the engine is running. There is not an indicator light or voltage meter on the engine.","question":"how can you tell if the charger on an XP 18HPE Duromax is working","id":5573},{"answer":"I'm going to write this all here, again, but if you call (844-DUROMAX) or email (support@duromaxpower.com) our Service Department they can send a copy of this to you with photos. To Wire the XP18HPE Key Switch: The black wire with the right angle connector connects to the spade on the starter solenoid. The black covered wire with eye connection connects to the left solenoid bolt The positive battery cable connects to the left bolt solenoid, then the split washer, then then 2nd nut. The brown wire with the male connector from the key switch connects to the brown wire with the female connector coming from under the recoil housing. Disconnect the ground relay (gold box, two wires) and the stop switch wire coming over the engine block (starts at the Ignition coil). The black wire with the female connector and green cap connects to the yellow wire with the male connector and the green cap from the ground relay. The black wire with the male connector and the green cap connects to the black wire with the female connector and the green cap from the stop switch. Ground the negative battery cable to the engine block at the key switch bolt, and then connect the battery positive and negative leads. You\u2019re good to go!","question":"how to wire an electric start key switch?","id":5248},{"answer":"CCW when looking at the shaft.","question":"Does this engine run clockwise or counterclockwise","id":5071},{"answer":"The charging coil is only 1.5 amps. You will end up draining the battery.","question":"Am I able to run headlights on a golf cart with this motor or will it drain the battery. Thanks. ","id":4697},{"answer":"The XP18HPE has a 1.5A charging coil to recharge the battery after starting.","question":"Does this have a generator to charge battery for electronic start?","id":4313},{"answer":"Yes, the engine is equipped with a governor for over speed protection.","question":"does this engine XP18HPE have a governor?","id":3710},{"answer":"I'm going to write this all here, but if you call (8044-DUROMAX) or email our Service Department they can send a copy of this to you with photos.\r\n\r\nTo Wire the XP18HPE Key Switch: The black wire with the right angle connector connects to the spade on the starter solenoid. The black covered wire with eye connection connects to the left solenoid bolt\r\nThe positive battery cable connects to the left bolt solenoid, then the split washer, then then 2nd nut. The brown wire with the male connector from the key switch connects to the brown wire with the female connector coming from under the recoil housing. Disconnect the ground relay (gold box, two wires) and the stop switch wire coming over the engine block (starts at the Ignition coil). The black wire with the female connector and green cap connects to the yellow wire with the male connector and the green cap from the ground relay. The black wire with the male connector and the green cap connects to the black wire with the female connector and the green cap from the stop switch. Ground the negative battery cable to the engine block at the key switch bolt, and then connect the battery positive and negative leads. You\u2019re good to go!\r\n","question":"I have no diagram to hook up the wiring and I can't figure out where all wires go to","id":4163}]}
